But don't panic––this problem is almost always easy to fix. The thread on a bobbin should be as smoothly wound as the thread on a purchased spool of thread. It should have some resistance but the thread moves freely. Check to see whether the bobbin is placed correctly in the bobbin case.

3. To wind the bobbin, insert the thread through the hole in your spool and then wind it around the bobbin a couple of times. If you don’t have the manual, it can be tricky to thread the machine and wind the bobbin. Perfect for beginners and hobbyists. Now that your bobbin is wound, get it inserted into the Singer sewing machine and it's ready to start sewing. You can cut the stray thread at the top of the bobbin once the bobbin is partially wound, or you can wait until the process is complete to cut it. This is especially important if you are running out of bobbin thread in the middle of topstitching or when you are sewing leather. A bird's nest of loopy, tangled bobbin thread on the underside of your sewing is one of the most common sewing machine problems to quickly derail any project you're working on. This video shows how to thread your bobbin on a side threading sewing machine. Put end of thread through the hole in bobbin as shown.

Place bobbin onto shaft with end of thread coming from top of bobbin. Make sure to watch the thread as it winds, to make sure it winds evenly and does not end up going off of your bobbin. The lower thread comes from the bobbin, a small spool of thread that’s loaded under the slide plate of the machine. I’ve written about my Singer 66 before, but I wanted to share some videos I prepared about this fantastic, reliable vintage sewing machine.

The SINGER START sewing machine gives beginning sewists and hobbyists just enough features to get their creativity off the ground.

(The brake may have been adjusted if the thread on the bobbin exceeds the edges of the bobbin and will need to be readjusted according to your manual so the threading stops before the bobbin is over-wound.) One of the most difficult things about learning to use a sewing machine is getting the basic machine functions down. Start every project with a full bobbin and fill a few bobbins for the project at once so when your bobbin thread runs out you have another one ready.

8. Insert the bobbin making sure the bobbin rotates counterclockwise when you pull the thread. The Singer Touch & Sew machine from the 1970s is an amazingly versatile machine still appreciated by Singer enthusiasts. 3. Watch this video sewing tutorial and learn how to insert the bobbin into a Singer … To wind your bobbin, start by placing your spool of thread on the machine, and threading the (first) top thread guide, as you would if you were threading the machine. The upper thread guide when moved to the most top of its travel, the needle is in the most upright position.Then you take the bobbin case and your bobbin.

The bobbin is a small spool of thread that is loaded underneath your needle and it supplies the thread that comes up through the base of your machine. I start by plasing the bobbin in its casing.

Even with its simplistic design, often getting started takes a bit of time, concentration and practice. (Winding stops automatically once bobbin is full.) Then look for another thread guide that is out of place, down lower or off to another side, and wrap your thread …

10.

Start winding the bobbin for a few seconds by pushing down on the foot pedal or by pressing the bobbin winding button (if your machine has one).

Push bobbin winder shaft to the right until it clicks.

2. 9. For example, the 700 series featured automatic needle threading and the "wind in place" bobbin. Finally I test my bobbin to make sure the bobbin turns counter clockwise in the casing. We start off by making sure that the needle is in the most upright position. Holding thread end, step on speed controller to run the machine until the desired amount of thread is wound. You should try tugging on the threads when you start sewing, both the upper and bobbin threads.

It’s a two-part process in which you’ll learn how to wind the bobbin and then thread the machine.

Cut thread; push bobbin to the left and remove it from bobbin winder pin (illustration 4). This thread connects with the thread on your needle and forms stitches.

Without the bobbin casing properly in … Replacing the bobbin case after changing the thread spool gets you back to sewing. Bobbin cover will pop up sufficiently to allow you to remove the cover. A singer sewing machine sews with two threads: an upper and lower thread.

Wind the thread through all the threading points--the thread guide on the top of the sewing machine, the tension discs and the takeup lever.

NOTE: This is a very important step as the bobbin can become unthreaded and cause sewing problems if it rotates clockwise.

Hold the end of thread.

Place a spool of thread on the horizontal spool holder on top of the Singer 756.